0

M-FLOOR 800 – Heavy Duty Line Marking Paint

Was created to provide a durable, chemical and abrasion resistant line marking coating for industrial and business applications to steel and concrete substrates.

£74.40 Excl VAT

Clear

Description

M-FLOOR 800 – Heavy Duty Line Marking Paint

The material has been created to offer a durable, chemical and abrasion resistant line marking coating for industrial and business applications to concrete and steel surfaces.

M-FLOOR 800 is supplied as a two pack system, comprising pre-weighed quantities of Base and Curing Agent that after mixing together, can be easily applied by brush or roller to make a chemical and abrasion resistant finish.

Ideal as a line marking material for industrial and commercial flooring to demarcate parking bays, walkways, aisles, etc

Typical Uses

  • As a lining material for industrial and commercial floors.
  • To demarcate parking bays, walkways, aisles, etc.

Please contact us to discuss your project before purchasing this material to confirm suitability.

Application Guide

  • All oil and grease must be removed from the surface using an appropriate cleaner such as MEK or similar type solvent.
  • All surfaces must be abrasive blasted to ISO 8501/4 Standard SA2.5 (SSPC SP10/ NACE 2) minimum blast profile of 75 microns using an angular.
  • Once blast cleaned the surface must be degreased and cleaned using MEK or similar type solvent.
  • All surfaces must be coated before gingering or oxidation.
  • All oil and grease must be removed from the surface using an appropriate cleaner such as MEK.
  • All surfaces must be mechanically abraded using handheld grinders to ISO 8501/4 ST3 (SSPC SP3 ST3).
  • Once abraded, the surface must be degreased and cleaned using MEK or similar type material.
  • All surfaces must be repaired before gingering or oxidation occurs.

New Concrete

  • Allow new concrete to cure for a minimum of 21 days and/or
    the residual moisture content should be below 6%.
  • Lightly abrasive blast or scarify to remove any surface laitance.
  • Clean all dust and debris from the surface.
  • Blow holes and defective concrete shall be made good using a proprietary repair compound.
  • Existing coatings should be sound and free from contaminants.
  • Suitable mechanical treatment such as vacuum gritblasting is the preferred treatment prior to application as this ensures a mechanical “key” for the coating.

 

  • Do not apply to wet or uncured concrete surfaces.
  • Do not apply at temperatures of 3°C or less.
  • Transfer the contents of the Curing Agent unit into the Base container.
  • Using a low speed electric paddle mixer, mix the 2 components until a uniform material free of any streaks is achieved.
  • Once mixing is complete use the mixed paste as soon possible after mixing.

Brush & Roller

  • Pour the mixed material into a paint kettle or paint tray (this will maximise the usable life).
  • Stripe coat all edges, joints & corners.
  • Apply at a nominal rate of 0.40-0.80kg/m².
  • Allow to cure for a minimum of 5 hours @ 20°C prior to light foot traffic access and 10 hours @ 20° prior to vehicular trafficking.
  • 7 days cure @ 20°C is recommended prior to exposure to chemicals.
Appearance

Colours: Safety Yellow
(BS4800 or RAL colours on request)
Usable Life20°C
10°C


20 minutes
40 minutes


Coverage
5kg pack is sufficient to coat 6.25 -12.50 m2 of surface 6.25 – 12.50 m2

Cure Times at 20°C Tack free time
Hard dry time
Full chemical resistance
2 hours
5 hours
7 days
Adhesion strength
Concrete
3.9MPa (concrete failure)
Chemical ResistanceChemical resistance: excellent resistance to dilute acids,
dilute alkalis, oil, petrol, diesel, vegetable oils.
Please consult our Technical Department for specific advice

Storage LifeStore in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C. Minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions

Min 12 months

Additional information

Colour

White, Yellow

Unit Size

2.5kg

Reviews

There are no reviews yet.

Be the first to review “M-FLOOR 800 – Heavy Duty Line Marking Paint”

Your email address will not be published. Required fields are marked *