Previous
M-CERAMIC 100 - Epoxy Ceramic Putty

M-CERAMIC 100 – Epoxy Ceramic Putty

£97.30£247.00 Excl VAT
Next

M-CERAMIC 600 – Epoxy Ceramic Underwater Coating

£291.70 Excl VAT
M-CERAMIC 600 - Epoxy Ceramic Underwater Coating
M-CERAMIC 700 - Polyurethane Impact Resistant Coating

M-CERAMIC 700 - Polyurethane Impact Resistant Coating

£125.00 Excl VAT

M-CERAMIC 700 – Polyurethane Impact Resistant Coating

£125.00 Excl VAT

Is an Impact & Wear Resistant Coating, ideally suited for abrasive slurries and aggregates. Commonly used to protect chutes & Pumps ect….

 

Description

M-CERAMIC 700 - Polyurethane Impact Resistant Coating

Is a flexible high build solvent-free Polyurethane Imact Resistant Coating designed for applications subject to impact, wear and abrasion from slurries and aggregates ect….

The material is designed to be applied as a multi coat system, with a minimum cured coating thickness of 1.0mm. This can be achieved by using a brush, roller or squeegee typically 2 x 500 micron coats is achievable on horizontal surface. For vertical surfaces 3 coats may be required.

Application Guide

  • All oil and grease must be removed from the surface using an appropriate cleaner such MEK or similar type solvent.
  • All surfaces must be abrasive blasted to ISO 8501/4 Standard SA2.5 (SSPC SP10/ NACE 2) minimum blast profile of 75 microns using an angular.
  • Once blast cleaned, the surface must be degreased and cleaned using MEK or similar type solvent.
  • All surfaces must be coated before gingering or oxidation.
  • All oil and grease must be removed from the surface using an appropriate cleaner such as MEK.
  • All surfaces must be mechanically abraded using handheld grinders to ISO 8501/4 ST3 (SSPC SP3 ST3).
  • Once abraded, the surface must be degreased and cleaned using MEK or similar type material.
  • All surfaces must be repaired before gingering or oxidation occurs.

Prior to mixing please ensure the following:

  • The base component is at a temperature between 15-25°C.
  • Do not apply the material when the ambient or substrate temperature is below 10°C or less than 3°C above dew point.
  • Transfer the contents of the Activator unit into the Base container.
  • Using a slow speed electric paddle mixer, mix the 2 components together until the material is streak free.
  • Once mixing is complete, use the mixed coating as soon possible after mixing.

Use all mixed material within 15 minutes at 20°C.

  • Pour the mixed material into a paint kettle or paint tray (this will maximise the usable life)
  • Using a 50mm synthetic brush, stripe coat all edges, joints & corners.
  • Once the stripe coat has cured sufficiently and is capable of being overcoated, apply the basecoat to all surfaces at minimum 350 microns.
  • Once the basecoat of material has cured sufficiently, approximately 6-8 hours at 20°C, apply the intermediate coat to all surfaces at a minimum 350 microns.
  • Once the intermediate coat has cured sufficiently, approximately 6-8 hours at 20°C, apply the topcoat to all surfaces at a minimum 350 microns.
  • Minimum finished coating thickness needs to be in excess of 1000 microns.
AppearanceBase
Activator
Mixed
Blue or light grey thixotropic liquid
Amber liquid
Blue or light grey Thixotropic liquid
Mixing RatioBy Weight
By Volume
3.25:1
3:1
DensityBase
Activator
Mixed
1.31
1.22
1.29
Solids Content100%
Sag ResistanceNil at: 400microns
Usable Life10°C
20°C
30°C

25-35 minutes
15-20 minutes
8-10 minutes

Coverage

2 x 350microns
The material should be applied at a minimum wet film thickness of 350 microns per coat.





2.85 sqm/ ltr
Cure TimesMovement without load or immersion:
Light loading:
Full loading/water immersion:
Chemical Contact:
2 hours
8 hours
3 days
14 days
Storage LifeUnopened and stored in dry conditions (15-30°C)2 years
AdhesionTensile Shear to ASTM D1002 on abrasive blasted mild steel with 75 micron profile169kg/cm² 2400psi
Corrosion ResistanceTested to ASTM B1175000 hours
Flexibility(British Gas FW0028 Draft method)
3% Strain at 20°C
3% Strain at 5°C
3% Strain at 0°C ASTM D522
Pass
Pass
Pass
Pass
HardnessShore D to ASTM D224080
Impact Resistance(British Gas CW6) 15 Joules (BS EN 10290)
23°C 8.6 Joules
5°C 6.1 Joules
Adhesion – Resistance to Removal (BS EN 10290)
23°C rating 1
60°C rating 2
Adhesion – Pull Off Test(BS EN 10290)
23°C 175kg/ cm²
60°C 73kg/ cm²

(ASTM D4541) 214kg/ cm²
Electrical Insulation
Resistance
(BS EN 10290)8.4 X 10⁹
Indentation Resistance(BS EN 10290)23°C 0.1mm
60°C approx. 15%
Flexibility(BS EN 10290)Pass
Elongation(BS EN 10290)14.5%
Abrasion Resistance(ASTM D4060)90mgm weight loss per 1000 cycles
1kg load – CS17 wheel
Heat ResistanceSuitable for use in immersed conditions at temperatures up to:
Suitable for use in dry conditions at temperatures up to dependant on load:
70°C
120°C
Chemical ResistanceAt 20°C product resists attack by a wide variety of inorganic acids, alkalis, salts and organic mediaAcetic Acid 10%
Benzoic Acid 15%
Caster Oil
Cyclohexane
Ethyl Alcohol 50%
Formic Acid 10%
Fuel Oil
Glycerine
Hydrochloric Acid 20%
Isopropanol
Lactic Acid 20%
Mineral Oil
Nitric Acid 10%
Phosphoric Acid 50%
Potassium Hydroxide 10%
Sodium Carbonate 10%
Sodium Hydroxide 10%
Sulphuric Acid 50%
White Spirit

Additional information

Weight N/A
Unit Size

2ltr

Kit Contents

1 x Plastic Applicator Tool, 1 x Plastic Spatula

Colour

Blue, Light grey

Mixing Ratio

3:1 By Volume, 5:1 By Weight

Material

Polyurethane

Number of Coats

2

Pot Life @ 20°C

20/ 25 Mins

Manufacturer

Maxkote

Shopping cart

1

Subtotal: £317.70

View basketCheckout