M-FLOOR 103 – Anti-Static Epoxy Floor Coating

Is formulated using the latest 100% solids, solvent-free epoxy resins. When mixed, the product is simple to apply with a brush or roller. Suitable for areas of use where the resistance of fewer than 10⁸ ohms are required.

Tags: , ,

£165.00 Excl VAT


Out of stock


M-FLOOR 103 – Anti-Static Epoxy Floor Coating

Maxflo 200 – Anti-static epoxy floor coating is formulated using the latest 100% solids, solvent-free epoxy resins. When mixed, the product is simple to apply with a brush or roller.

Suitable for areas of use where the resistance of fewer than 10⁸ ohms is required as a measure to control static electricity. Once cured Maxflo 200 has a tough and easily cleaned high gloss finish that is resistant to a wide range of chemicals. With the addition of an aggregate, the product is suitable for a variety of anti-slip options.

Once cured the product provides following characteristics:

  • Range of colours
  • Anti-static
  • Excellent adhesion
  • Chemical attack
  • Hygienic and easily cleaned





  • Concrete surfaces
  • Explosion risk areas
  • Hospitals
  • Chemical factories
  • Electrical component manufacure
  • Solvent-free
  • 100% Solids material
  • Chemical resistance
  • Excellent wear characteristic
  • Outstanding corrosion resistance
  • Two colour system
  • Easy mix formulation
  • Safe to use in a confined space
  • No coating shrinkage or cracking
  • Resists wide range of chemicals
  • Protects for longer
  • long-term
  • Helps to monitor coating wear
  • Aids application on site

Application Guide
Technical Data
Application Guide

  • Prepare the surface
  • Mix the material
  • Apply the base at a  target film thickness of 250-300 microns
  • Apply top-coat at a target film thickness of 250-300 microns
  • Allow for curing
  • Inspect the coating for any pinholes or misses and repair where necessary
Surface Preparation steel

Degrease the repair area with MEK or similar solvent to remove any surface contamination, using angular grit, grit-blast to SO 8501/4 Standard SA2.5 (SSPC SP10/ NACE 2) and a minimum blast profile of 75 microns.

Once blast cleaned, the surface must be dust free and cleaned again using MEK or similar solvent. All surfaces must be repaired or coated before oxidation or gingering occurs.

Surface preparation concrete

Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc. Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. MaxCrete 200 concrete repair mortar.

Block work shall be sealed using MaxPrime 100 surface sealer/ primer . Suitable mechanical treatment such as vacuum grit blasting is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating.


Pour the contents of the activator container into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved. for small quantities us a mixing ratio of:

2:1 by weight
Application Base Coat

Apply by brush, roller or airless spray at a nominal rate of 0.25 to 0.3kg/m². After a minimum of 14 hours and before a maximum of 48 hours, apply a second coat at the
same rate. Should a non-slip finish be required, then broadcast an appropriate aggregate such as Quartz, immediately after the first coat. Brush off excess aggregate the following day, prior to applying the second coat.



Usable life at  20°C

45 minutes

Over-Coating Times

Minimum – the applied material can be over-coated as soon as it is touch dry.

Maximum – over-coating time 36 hours.

Where the maximum over-coating time is exceeded, the material should be allowed to harden before being abraded or flash blasted to  remove any surface contamination

Technical Data

Additional information


Dark Grey

Unit Size



There are no reviews yet.

Be the first to review “M-FLOOR 103 – Anti-Static Epoxy Floor Coating”

Your email address will not be published. Required fields are marked *