M-METAL 700 – Metal Epoxy Putty – Extended Cure

£275.60 Excl VAT

Loading...

Description

M-METAL 700 – Metal Epoxy Putty – Extended Cure

Is a Extend Cure Metal Epoxy Putty, suitable for large repair areas where extra pot life is required.

The product is supplied in two parts with a base and activator once mixed M-METAL 700 provides a smooth grey paste ideally suited for repairs to steel components and other metallic surfaces. 

The mixed the material can be applied in a single coat up to a thickness of 20.0mm without slumping.

When mixed the product has a standard has a pot life of 60 mins. Once cured it is readily drilled and machined to fine tolerances or can be sanded to achieve the desired profile of the repair.

Typical Uses

  • Machinery Shimming and Choking
  • Large Shaft Repairs
  • Pump Casing Defects
  • Repair Worn Bearing Housings
  • Leaking Flange Repairs
  • Leaking Tank Seams
  • As a Structural Adhesive

Application Guide

  • All oil and grease must be removed from the surface using an appropriate cleaner such MEK or similar type solvent.
  • All surfaces must be abrasive blasted to ISO 8501/4 Standard SA2.5 (SSPC SP10/ NACE 2) minimum blast profile of 75 microns using an angular.
  • Once blast cleaned, the surface must be degreased and cleaned using MEK or similar type solvent.
  • All surfaces must be coated before gingering or oxidation.
  • All oil and grease must be removed from the surface using an appropriate cleaner such as MEK.
  • All surfaces must be mechanically abraded using handheld grinders to ISO 8501/4 ST3 (SSPC SP3 ST3).
  • Once abraded, the surface must be degreased and cleaned using MEK or similar type material.
  • All surfaces must be repaired before gingering or oxidation occurs.

Prior to mixing please ensure the following:

  • The base component is at a temperature between 15-25°C.
  • The ambient & surface temperature is above 5°C or less than 3°C  above dew point.
  • Mix PART B with PART A in full units as supplied.
  • For small quantities us a mixing ratio of: 3:2 BY VOLUME OR 1.7:1 BY WEIGHT   
  • When mixing both materials, it is very important to have a uniform streak free fluid.

Use all mixed material within 60 minutes at 20°C.

  • Using a short-bristled brush, spatula or applicator tool, apply the material to the prepared repair area.
  • Ensure the product is pressed into any holes, scars or cracks before building up to the the quired thickness.
  • Minimum – the applied material can be over-coated as soon as it is touch dry.
  • Maximum – the over-coating time should not exceed 6 hours.

Where the maximum over-coating time is exceeded, the material should be allowed to harden before being abraded or flash blasted to remove surface contamination.

AppearanceBase
Activator
Mixed
Dark grey paste
Light grey paste
Mid grey paste
Mixing RatioBy Weight
By Volume
1.67:1
3:2
DensityBase
Activator
Mixed
2.7
2.4
2.58
Volume Capacity388cc/kg
Solids Content100%
Slump ResistanceNil at2.0 cm
Usable Life20°C
30°C

60 minutes
30 minutes

Coverage1kg at a thickness of 1.0mm0.38m2
Cure Times @ 20°CMovement without load or immersion:
Machining and light loading:
Full loading:
Immersion:
5 hours
12 hours
4 days
7 days
Storage LifeUnopened and stored in dry conditions (15-30°C)5 years
AdhesionTensile Shear to ASTM D1002 on abrasive blasted mild steel with 75 micron profile180kg/cm² 2550psi
Compressive StrengthTested to ASTM D 695839kg/ cm² 11,900psi
Flexural StrengthTested to ASTM D790585kg/cm² (8300psi)
HardnessShore D to ASTM D224087
Heat ResistanceSuitable for long term water immersion at temperatures up to 60°C. Resistant to dry heat in excess of 180°C dependant on load.60°C
180°C
Chemical ResistanceThe product resists attack by a wide variety of inorganic acids, alkalis, salts and organic media.

M-METAL 700 – ACTIVATOR – MSDS

M-METAL 700 – BASE – MSDS

Additional information

Weight 4 kg
Unit Size

4kg

Kit Contents

1 x Plastic Applicator Tool, 1 x Plastic Spatula

Colour

Dark Grey

Mixing Ratio

1.7:1 By Weight, 3:2 By Volume

Number of Coats

1 – 20mm max

Pot Life @ 20°C

60 Mins

Coverage per Unit

0.388 sqm at 1.0mm

Reviews

There are no reviews yet.

Be the first to review “M-METAL 700 – Metal Epoxy Putty – Extended Cure”

Your email address will not be published. Required fields are marked *

Related Products